If the room is too cold or exposed to draughts then incubator will be unable to regulate the temperature, this can cause the heating element to fail. For best results please ensure that your incubator is located in a room with a minimum temperature of 18c. Some breeders will turn the temperature down for hatching time, if this is something you did on your previous hatch ensure you have turned it back to the correct temperature. If you have an incubator which does not have a display refer to the manufacturer’s instructions on how to turn the temperature up using the adjustment screw. Set temperature, check the set temperature and ensure it is set correctly.There are a few reasons why your incubator may not be getting to temperature, sometimes it can be due to a fault but more often than not its due to the environment the incubator is in and how well it is looked after. If you are still experiencing issues with the temperature, please contact us here. Tap water will cause a scale build up on the sensors which can cause inaccurate readings. It is also good practice to ensure that you use distilled or deionised water in any incubator rather than normal tap water. If you don’t routinely clean the incubator before and after each hatch and remove all hatching debris such as eggshell, feathers and dust it will affect how well the incubator performs and how accurate the reading is. If the fan is covered in feathers and dust this will affect how well the fan performs and, in turn, affects how well it can circulate the air around the incubator. Check that nothing is caught or obstructing the fan from running fast and continuously. Ideally the room should be at a stable temperature of around 18☌-22☌. Ensure the incubation room is at the correct temperature. If you have an incubator which does not have a display, please refer to the manufacturer’s instructions on how to turn the temperature down using the adjustment screw. Check the set temperature and ensure it is set correctly. It is therefore best to check the following: Poor maintenance and lack of cleaning can also cause your incubator to overheat. An incubator should never be near a window, radiator, or other external heat source. Sometimes this can be due to a fault, but more often it is due to the incorrect environment the incubator is operating in. There are a few reasons why your machine's temperature could be going past the set level. You can find more information on recommended temperature and humidity settings here. If you do change the temperature for the last 3 days, always ensure that you set it back to the correct temperature when you come to start your next hatch. All Incubators without a digital temperature display should be factory set to 37.5☌ to 37.8☌.įor some breeds it is recommended to lower the temperature for the final 3 days before hatch. To find exactly where this is located on your Incubator, check the instructions, as they will also detail which way to turn the screw to either increase or reduce the temperature. The temperature can then be adjusted by turning the adjustment screw located on the top of the Incubator. If you have a Incubator like the Mini II Eco, Maxi II Eco, Rcom 10 Eco or the Rcom King Suro Eco 20 which does not have a digital display and only has a liquid glass thermometer: ensure you take a reading form the thermometer once the Incubator has been running for at least 1-2 hours. To change the settings press OK, or to exit the menu continue to press the + button until you see the SAVE option. On the Brinsea Incubators the set up can vary so please check the instructions, but normally if you press the + and – buttons together it will unlock the menu and show you the current settings. On River Systems/ET Incubators, pressing the + and – buttons will show you the current setting and pressing either the + or – button will allow you change the setting. On Rcom Incubators with a digital display, you can simply press the OK button and it will show you what the incubator is currently set at. The instruction handbook contains all of the information you will need for the correct set-up, along with the correct incubation temperatures which are normally 37.5 to 37.7☌ Our Egg Incubators are all factory calibrated at their correct operating temperatures during manufacture, but best practice is always to check these settings each time you prepare for incubation.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |